Corrosion Protection of Offshore Wind Energy Constructions in Germany: Challenges and Approaches

P. Plagemann, A. Momber

Abstract


The significant increase in the share of renewable energies within the next decades has high political relevance in Germany. Due to the high availability and rate of yield for wind, offshore wind energy plants are of particular interest. Currently, wind energy plants with power ratings up to 8 MW and rotor blade diameters up to 150 m are raised near the German coast. To operate these devices economically, service lives of 25 years or more are required. Here, corrosion is an important limiting factor, as the devices are constantly exposed to a highly corrosive environment (sea water, saline air). In this paper, general conditions and specific technical challenges to protect offshore wind energy plants from corrosion are described, and some examples of technical solutions are presented. Some of the reported solutions have been developed in nationally funded joint research projects between research institutions and industrial companies, representing the full supply chain for offshore wind energy plants.

Keywords


Corrosion Failure; Offshore Wind Energy Plants; Protective Coatings; Repair Concepts;

Full Text:

PDF

References


Renewable Energies Agency, under support of the Federal Ministry for Economic Affairs and Energy and the Federal Ministry of Food and Agriculture of Germany, www.unendlich-viel-energie.de, Status 2017

DNV-OS-J101, “Design of offshore wind turbine structures”, May 2014

“Korrosionsschutz von offshore-Windenergieanlagen”, GfKORR - Gesellschaft für Korrosionsschutz e. V. („Corrosion protection of offshore wind power plants”, GfKORR (German Society for Corrosion Protection) , ISBN 978-3-9354,6-61-1, Theodor-Heuss-Alle 25, 60486 Frankfurt am Main, Germany.

DIN EN ISO 12944 Part 1 -8, “Paints and varnishes - Corrosion protection of steel structures by protective paint systems”, International Standardization Organization (ISO)

E-DIN EN ISO 12944-9:2017-05 “Paints and varnishes-Corrosion protection of steel structures by protective paint systems-Part 9: Protective paint systems and laboratory performance test methods for offshore and related structures”, International Organization for Standardization (ISO)

ISO 20340:2009, “Paints and varnishes-Performance requirements for protective paint systems for offshore and related structures”, International Organization for Standardization (ISO)

Norsok M 501, “SURFACE PREPARATION AND PROTECTIVE COATING”, Edition 6 (2012), Norwegian Technology Standards Institution, NORWAY

A. Momber et al., “A holistic concept for coating monitoring and maintenance on offshore wind power constructions” EUROCORR 2015, 6. -12. 9. 2015, Graz/Austria

DIN EN ISO 8501-3:2006, “Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness-Part 3: Preparation grades of welds, edges and other areas with surface imperfections”, International Organization for Standardization (ISO)

“RepaKorr-Reparatursysteme und -konzepte für Korrosionsschutzbeschichtungen von Offshore-Windenergieanlagen“, („RepaKorr-repair systems and concepts for corrosion protective coatings of offshore wind power plants“, joint research project funded by Federal Ministry of Education and Research, grand ID 03X3570A, 01.04.2013-31.03.2016

A.W. Momber, S. Buchbach, P. Plagemann, T. Marquardt, I. Winkels, J. Viertel, “Effects of surface preparation and coating type on the corrosion protection performance of repair coatings for offshore wind power constructions”, Materials and Corrosion, 11 2017

DIN EN ISO 9227, “Corrosion tests in artificial atmospheres-Salt spray test”, International Organization for Standardization (ISO)


Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution 3.0 License.

ISSN: 2180-1843

eISSN: 2289-8131