THE EFFECT OF DIESEL AND BIO-DIESEL FUEL DEPOSIT LAYERS ON HEAT TRANSFER
H.F. Shurvell, A.D.H. Clague and M.C. Southby, “Method for determination of the composition of diesel engine piston deposits by infrared spectroscopy”, Journal of Applied Spectroscopy, vol. 51, no. 6, pp. 827-835, 1997.
O. Guralp, M. Hoffman, D. Assanis, Z. Filipi, T.W. Kuo, P. Najt and R. Rask, “Characterizing the effect of combustion chamber deposits on a gasoline HCCI engine”, SAE Technical Paper, 2006-01-3277, pp. 1-14, 2006.
Z. Ye, Q. Meng, H.P. Mohamadiah, J.T. Wang, L. Chen and L. Zhu, “Investigation of deposits formation mechanisms for engine in-cylinder combustion and exhaust system using quantitative analysis and sustainability study”, International Journal of Thermophysics, vol. 28, no. 3, pp. 1056-1066, 2007.
J.B. Heywood, Internal combustion engine fundamentals, New York: McGraw Hill, 1988.
S.M. Muzikus, M.I. Fedorov and E.I. Frolov, “Standard allowable limit for carbon-deposit formation in diesel engines”, Chemistry and Technology of Fuels and Oils, vol. 11, no. 10, pp. 815-817, 1975.
Y. Yamada, M. Emi, H. Ishii, Y. Suzuki, S. Kimura and Y. Enomoto, “Heat loss to the combustion chamber wall with deposit in D.I. diesel engine: variation of instantaneous heat flux on piston surface deposit”, JSAE Review, vol. 23, no. 4, pp. 415-421, 2002.
P. Eilts, “Investigation on deposit formation during low load operation of high supercharged diesel engines,” in the International Symposium on Diagnostics and Modeling of Combustion in Internal Combustion Engines (COMODIA), Kyoto, Japan, 1990, pp. 517-522.
M.Z. Akop, Y. Zama, T. Furuhata, M. Arai, “Characteristics of Adhesion of Diesel Fuel on Impingement Disk Wall. Part 1: Effect of Impingement Area and Inclination Angle of Disk”, Atomization and Sprays, vol. 23, no. 8, pp. 725-744, 2013.
M.Z. Akop, Y. Zama, T. Furuhata and M. Arai, “Experimental investigations on adhered fuel and impinging diesel spray normal to a wall”, Atomization and Sprays, vol. 23, no. 3, pp. 211-231, 2013.
X. Zhou, T. Li, Z. Lai and Y. Wei, “Modeling diesel spray tip and tail penetrations after end-of-injection”, Fuel, vol. 237, pp. 442-456, 2019.
S. Yang, X. Li, D.L.S. Hung, M. Arai and M. Xu, “In-nozzle flash boiling flow of multi-component fuel and its effect on near-nozzle spray”, Fuel, vol. 252, pp. 55-67, 2019.
H. Ishii, M. Emi, Y. Yamada, S. Kimura, K. Shimano and Y. Enomoto, “Heat loss to the combustion chamber wall with deposit adhering to the wall surface in D.I. diesel engine. First report: Influence of deposit on instantaneous heat flux into the piston surfaces”, SAE Technical Paper, 2001-01-1811, pp. 1-13, 2001.
G. Lepperhoff and M. Houben, “Mechanisms of deposit formation in internal combustion engines and heat exchangers”, SAE Technical Paper, 931032, pp. 1-12, 1993.
T.W. Zerda, X. Yuan and S.M. Moore, “Effects of fuel additives on the microstructure of combust ion engine deposits”, Carbon, vol. 39, no. 10, pp. 1589-1597, 2001.
Y.M. Arifin, “Diesel and bio-disel fuel deposits on a hot wall surface”, Ph.D. thesis, Gunma University, Japan, 2009.
© Journal of Advanced Manufacturing Technology